Static Pushover analysis on a Bridge Model.
Re: Static Pushover analysis on a Bridge Model.
What element type are you using - DB (displacement-based) or FB (force-based)? If DB, you may need to subdivide elements. Just a thought. Also double-check units.
Tim Huff
-
- Posts: 6
- Joined: 14 May 2020, 21:52
Re: Static Pushover analysis on a Bridge Model.
Thank you for your reply.
I am using DB elements. My units are fine. I am not sure what do you mean by subdividing elements. Do you mean the division of elements in the element subdivision tab in the Options menu for pre-processor?
Thank you,
Dipesh
I am using DB elements. My units are fine. I am not sure what do you mean by subdividing elements. Do you mean the division of elements in the element subdivision tab in the Options menu for pre-processor?
Thank you,
Dipesh
- seismosoft
- Posts: 1184
- Joined: 06 Jul 2007, 04:55
Re: Static Pushover analysis on a Bridge Model.
The infrmDB models are only accurate for small elements lengths. As a result, one has to subdivide each member at least to 4-5 elements, in order to achieve good results. If this seems inconventient, it would be better to use one of the force-based frame element models.
Seismosoft Support
Seismosoft Support
-
- Posts: 6
- Joined: 14 May 2020, 21:52
Re: Static Pushover analysis on a Bridge Model.
Thank you once again for your reply.
I did change my elements to infrmFB elements. However, I found that it gave me convergence problems. It was resolved when I removed the self-weight of concrete and reinforcements and then applying them to the section with additional mass/length. I also found that the deflections in my model are affected when I make changes in the Gravity and Mass tab in the Options in Pre-Processor.
I am sending my model to the email support@seismosoft.com with a brief description.
I did change my elements to infrmFB elements. However, I found that it gave me convergence problems. It was resolved when I removed the self-weight of concrete and reinforcements and then applying them to the section with additional mass/length. I also found that the deflections in my model are affected when I make changes in the Gravity and Mass tab in the Options in Pre-Processor.
I am sending my model to the email support@seismosoft.com with a brief description.
- seismosoft
- Posts: 1184
- Joined: 06 Jul 2007, 04:55
Re: Static Pushover analysis on a Bridge Model.
We checked briefly your model, the elements' lengths are rather small; the infrmDB is reasonably accurate, and the infrmFB element with 4-5 integration sections are too heavy and it can be expected that they lead to convergence problems.
Seismosoft Support
Seismosoft Support
-
- Posts: 1
- Joined: 06 Nov 2020, 21:22
modeling of masonry
my questions are:
1. can we perform micro modeling of masonry in seismostruct.
2. the masonry modeled in the published example is on equivalent frame based or some other approach?
3. if anyone have a research paper on masonry modeling in siesmostruct please provide me. not on infill but on pure masonry
for further guidance i shall be thankful
1. can we perform micro modeling of masonry in seismostruct.
2. the masonry modeled in the published example is on equivalent frame based or some other approach?
3. if anyone have a research paper on masonry modeling in siesmostruct please provide me. not on infill but on pure masonry
for further guidance i shall be thankful
- seismosoft
- Posts: 1184
- Joined: 06 Jul 2007, 04:55
Re: Static Pushover analysis on a Bridge Model.
Abd Ur Rahim,
1. No, SeismoStruct's masonry model is a macroelement
2. Refer to the User's manual for a detailed description of the model. it consists of three subelements, a internal fibre element to simulate bending (similar to the frame elements) with two inelastic link elements at the two ends to simulate the shear behaviour
3. no paper has been published yet with the details of the model, but there will e a paper soon
Seismosoft Support
1. No, SeismoStruct's masonry model is a macroelement
2. Refer to the User's manual for a detailed description of the model. it consists of three subelements, a internal fibre element to simulate bending (similar to the frame elements) with two inelastic link elements at the two ends to simulate the shear behaviour
3. no paper has been published yet with the details of the model, but there will e a paper soon
Seismosoft Support
-
- Posts: 8
- Joined: 09 Feb 2022, 12:58
Re: Static Pushover analysis on a Bridge Model.
Has the aforementioned paper on masonry modeling already been published or is it available?
- seismosoft
- Posts: 1184
- Joined: 06 Jul 2007, 04:55
Re: Static Pushover analysis on a Bridge Model.
No, unfortunately the paper has not been published. Please refer to the help and the user's manual of the program
Seismosoft Support
Seismosoft Support